Shah Sawar Building Construction Company Shah Sawar Building Construction CompanyBuilding Construction – Kuwait
Illustration: large-format porcelain tiles being laid with levelling clips in a villa hall in Kuwait

Porcelain Tile Flooring and Bathrooms in Kuwait: Large Formats, Laid Without Hollow Spots

From sorting the boxes to the last grout line: the Shah Sawar team installs porcelain and ceramic tiles in Kuwait villas, bathrooms and shops on a level floor with no hollow spots, and with proper falls in wet areas.

In short: a good porcelain floor depends on what is under it more than on the tile itself: a screed level to within 3 mm over 2 m, a flexible C2TE S1 adhesive combed on the floor and on the back of the tile, levelling clips for large formats, movement joints every 4–5 m, and in bathrooms a waterproofing layer and 1–2 % falls to the drain before the first tile. That is how we install porcelain and ceramic in Kuwait, and we tap-test every floor before handover.

Why porcelain is the villa floor of Kuwait

  • It absorbs neither water nor dust: porcelain absorbs under 0.5 %, so coffee stains and Kuwait's fine dust do not soak in.
  • It takes traffic: harder than ordinary ceramic, so it suits entrances, corridors and shops that see thousands of steps a day.
  • Cool underfoot: it does not hold heat like dark stone, and with the AC it stays comfortable in summer.
  • Fewer joints: 60×120 and 120×240 cm tiles mean easier cleaning and a look closer to natural marble.
  • Every look: marble-look, wood-look, cement-look and stone-look porcelain, in polished, matt or anti-slip textures.
  • Hygienic: no sealing or periodic polishing, cleaned with water and ordinary detergent.

This page is part of our tile and marble installation in Kuwait service within the interior decor and finishing division. The same tiling team works in villas, apartments, shops and restaurants, from the floor screed to the last joint.

Formats and types we install

Porcelain and ceramic formats and where each one fits
Format / typeWhere it fitsInstallation note
Porcelain 60×60 cmBedrooms, kitchens, apartmentsEasiest to lay, 2–3 mm joints
Porcelain 60×120 cmHalls, corridors, entrancesLevelling clips are a must; lay along the length of the room
Porcelain slabs 120×240 cmReception halls, majlis, entrance wallsTwo fitters per slab, suction cups, a truly level screed
Wood-look planks 20×120 cmBedrooms and modern majlisStaggered by a third of the length, not a half
Wall ceramic 30×60 and 40×120 cmBathroom and kitchen wallsBottom to top, cuts planned at the corners
Anti-slip porcelain R10–R11Bathroom, kitchen and wet entrance floorsTextured surface, cleaned with a soft brush
20 mm outdoor porcelainCourtyards, seating areas, pool surroundsSee the outdoor tiles and interlock page

We help you choose the format for the shape of the room: a long hall needs rectangular tiles running along its length, and a small room looks bigger with 60×120 tiles and grout in the same colour.

Illustration: adhesive combed with a notched trowel and a porcelain tile set with levelling clips

Preparing the floor: level before beautiful

Most tile problems in Kuwait do not start with the tile but with the screed under it. Before we lay a single tile we check three things:

  • Levelness: we check the screed with a laser and a 2 m straightedge; any deviation over 3 mm is corrected with a self-levelling compound or by repairing the screed, because adhesive is not a levelling material.
  • Soundness and moisture: a crumbly or damp screed means tiles that go hollow after a few months. We wait for a new screed to dry and remove dust and grease.
  • The starting point: we set out from the centre of the room, not from a wall, so the cuts are equal at both ends and no thin strip appears at the door.

In occupied homes we protect furniture and doors and work room by room, so part of the house stays usable.

Adhesive, grout and movement joints

Adhesive: porcelain does not absorb water, so it is not laid in ordinary cement mortar but in a flexible C2TE S1 adhesive that keeps its strength in Kuwait's heat. We comb it with a 10–12 mm notched trowel on the floor and skim the back of the tile (double buttering), so coverage exceeds 90 % and no voids are left to go hollow later. In summer we work in the cooler hours and in small batches, because the adhesive skins over within minutes.

Grout: 2–3 mm joints for rectified porcelain. We grout with epoxy in bathrooms, kitchens and shops because it does not stain or change colour, and with improved cement grout in bedrooms. Grouting starts no earlier than 24–48 hours after laying.

Movement joints: every 4–5 m in both directions, at door thresholds, columns and the base of walls, filled with flexible silicone rather than rigid grout. A floor that runs 10 m without a joint lifts at the first heatwave.

Porcelain in bathrooms: waterproofing, falls and drainage

Bathrooms in Kuwait are washed down every day, so a porcelain bathroom starts under the tile:

  • Waterproofing first: a liquid or membrane layer on the floor and 20–30 cm up the walls, and in the shower up to splash height. The systems are described on our waterproofing page.
  • Falls: 1–2 % towards the floor drain or linear channel, built into the screed rather than the adhesive, so no water stands behind the door.
  • Sequence: walls first from the second course, then the floor, then the first wall course sitting over the floor tile to cover the edge.
  • Details: built-in niches with a slight fall, aluminium trims or 45° mitred edges at external corners, and silicone where the floor meets the wall and around the basin and bath.
  • Anti-slip: bathroom floor porcelain rated at least R10, and in the shower R11 or small 10×10 mosaics with more joints for grip.

Large-format porcelain on bathroom walls gives the look of marble without the staining, and is water-jet cut around switches and mixers with precision.

Illustration: large-format porcelain being laid on a level screed in a villa hall

Large format without hollow spots: how we do it

  • Levelling clips: under every meeting of two tiles, so edges line up within 1 mm.
  • Double buttering, always: a 120×240 slab weighs over 30 kg and is never left sitting on scattered dabs of adhesive.
  • Suction cups and two fitters: the slab is carried and placed in one move, without sliding on the adhesive bed.
  • Cutting: a rail cutter for straight cuts, water-jet cutting for drain and switch openings, and edges smoothed.
  • Tap test before handover: we tap every tile with a rubber mallet; a hollow sound means relaying before grouting, not after.

Common mistakes in porcelain installation

  • Dot-and-dab adhesive: five blobs under the tile instead of full-bed combing, the number one cause of hollow and cracked tiles.
  • No fall in the bathroom: a perfectly flat floor collects water at the door.
  • Grouting too early: grouting the same day traps the adhesive's moisture and stains the joints.
  • No movement joints: long halls without a joint lift in summer.
  • Mixed batches: boxes from different production batches differ in shade, so we sort before laying.
  • Cutting without a layout: slivers at doors and corners give a floor away no matter how fine the tile.

How we carry out tiling, step by step

  1. Site visit and measurement: we measure the areas, check the screed and drains, and discuss format, colour and laying direction.
  2. Quotation and layout: tile quantities with wastage, adhesive and grout type, and the programme. Get a quote or message us on WhatsApp.
  3. Preparation: removal of old tiles where needed, screed levelling, and waterproofing and falls in wet areas.
  4. Sorting and setting out: tiles sorted by batch and shade, starting lines drawn from the centre.
  5. Laying: double buttering, levelling clips, level checked row by row.
  6. Grouting after 24–48 hours: epoxy or improved cement grout, then silicone at the flexible joints.
  7. Cleaning, inspection and handover: grout haze removed, tap test done, floor ready for walking after 24 hours and for heavy furniture after a week.

We work across all governorates of Kuwait: Capital, Hawally, Farwaniya, Ahmadi, Jahra and Mubarak Al-Kabeer.

Frequently Asked Questions

How long does it take to tile a 60 m² hall in porcelain?

Usually 3 to 5 working days including preparation, laying and grouting. It takes longer with 120×240 slabs or if the screed needs levelling first. We confirm the programme after the site visit.

Can porcelain be laid over old tiles?

Yes, if the old floor is sound, level and not hollow: we lay over it with a dedicated adhesive after keying the surface, noting that the floor level rises about 1.5 cm at the doors. In bathrooms we prefer removal so the waterproofing and falls can be done properly.

What is the difference between ceramic and porcelain?

Porcelain is fired at a higher temperature, so it is denser, harder and absorbs far less water, which suits floors, wet areas and outdoors. Ceramic is lighter and easier to cut and suits walls and low-traffic rooms.

Which grout is best for bathrooms and kitchens?

Epoxy grout: it absorbs neither water nor grease, does not stain or discolour, and cleans easily. It sets fast and needs an experienced fitter, so we grout small areas in sequence.

Is large-format porcelain suitable for upper floors and apartments?

Yes; its weight per square metre is close to ordinary tiles because it is only 6 to 10 mm thick. The challenge is not weight but screed levelness and moving the slabs through lifts and stairs, which we plan before delivery.

When can the floor be walked on after installation?

Light foot traffic after 24 hours, grouting after 24 to 48 hours, and heavy furniture or opening a shop after 5 to 7 days when the adhesive has fully cured.

Ready to Start Your Project?

Call us, send a WhatsApp message or email us to book a site visit and a clear written quotation.

Call Now WhatsApp Quote