Shah Sawar Building Construction Company Shah Sawar Building Construction CompanyBuilding Construction – Kuwait
Aluminium and glass partition system for an office in Kuwait

Aluminium, Glass and Steel Works in Kuwait

Most people search for an aluminium technician in Kuwait only when something has failed: a window that leaks, a jammed shutter, cracked glass. We treat aluminium, glass and steel as a designed package inside the building contract: measured after plastering and before the final paint, and coordinated with electrical, HVAC and finishing before fabrication, not squeezed in after the floors are laid.

In short: Aluminium, glass and steel works cover the windows, doors, securit glass partitions, glazed facades, roller shutters and fabricated steel (gates, balustrades, structural frames) of a building, measured and installed as one package. In Kuwait the profile choice (standard or thermal break), how well the opening type seals against dust, and anti-corrosive priming of every steel item decide how long the work lasts. Each opening is measured on site after plastering and before the final paint, and the written quotation names the profile system, glass type and finish before anything goes to fabrication.

Why this trade belongs inside the building package

The recurring complaints in Kuwaiti homes (water tracking in at the window edge, dust settling on the sill of a closed window, a shutter that scrapes, a cracked window sill) are rarely caused by the aluminium itself. They are caused by an opening built to one dimension and a frame fabricated to another, with the difference filled in silicone.

When the same contractor builds the wall and fits the frame, the opening is set true while the block work is going up, the shutter box or track is formed into the wall, the power point for a motorised shutter is stubbed out before conduits are buried, and the external sill is cast with a fall so water runs away from the frame. None of these can be corrected later without breaking concrete.

Windows and doors: standard profile vs thermal break

In Kuwait's climate the single most consequential choice is between a standard aluminium profile and a thermal break profile. Aluminium conducts heat extremely well. On a summer afternoon the outer frame heats up and passes that heat straight through to the inner frame, so the window radiates into the room; in winter the reverse happens and moisture condenses on the cold frame and runs down the wall.

A thermal break profile separates the outer and inner halves with an insulating polyamide strip, interrupting the heat path. In practice that means a lower cooling load in rooms with large glazed elevations, and no winter dripping on the frames.

Profile and glazing options compared for Kuwaiti conditions
OptionHeat insulationSound insulationMaintenanceBest suited to
Standard profile, single glazingPoorPoorMinimalStores, outbuildings and unconditioned service openings
Standard profile, double glazingModerateGoodMinimalInternal rooms with small elevations
Thermal break, double glazingHighVery goodModerateBedrooms, living rooms and any sun-facing elevation
Thermal break, reflective or low-E double glazingHighestVery goodModerateSouth and west elevations and villas with wide glazing
Frameless toughened securit glassLimitedModerateVery easyInternal partitions, shower enclosures, shopfronts
Laminated glassModerateExcellentModerateRooms facing busy roads and anywhere safety on breakage matters

Opening type matters too. Sliding sashes save space but are harder to seal against fine dust; casement sashes close onto a continuous perimeter gasket and seal dust and noise far better, which is why we usually recommend them for bedrooms on a main road.

Securit glass: partitions, shower enclosures, shopfronts

Frameless toughened glass, or securit, has become the default for internal partitions in villas and offices, for shop entrances, and for bathroom enclosures. It carries daylight deep into a plan and makes a space read larger, and because it is toughened it breaks into small blunt granules rather than long shards.

  • Office and living partitions: toughened panels on floor and head patch fittings, with frosted glass or applied film over part of the height where seated privacy is wanted.
  • Shower enclosures: set out to the actual fall of the bathroom floor rather than an assumed level, with a bottom seal that keeps water inside the tray area.
  • Shopfronts: securit doors on a floor spring rated for constant use, with stainless pull handles and secure top and bottom patches.
  • Glass balustrades: laminated toughened panels in an aluminium channel base or on stainless spider fittings, for stairs, balconies and mezzanines.
  • Entrance canopies: laminated glass on stainless arms, set to a fall so rain drains rather than ponding.

One practical rule governs all of it: toughened glass is cut and drilled before it is tempered, never after. Hinge, lock and handle positions therefore have to be settled on the drawing before sizes go to the factory. A change afterwards means a new panel, not an adjustment.

Glazed facades and curtain walling

Glazed elevations here are generally built one of two ways. A curtain wall hangs in front of the concrete frame and conceals it completely, giving an uninterrupted glazed face. A punched or infill system fills the openings between columns and beams; it is lighter on the structure and simpler to build, but the frame stays visible.

Either way, three details decide whether the facade performs: brackets anchored into sound concrete with fixings sized for dead load and wind, movement joints that let long aluminium runs expand and contract through Kuwait's seasonal swing without bowing, and drainage designed into the mullion sections so any water that gets past the outer seal is carried back out through weep points instead of collecting.

Roller shutters and when to motorise

A roller shutter is not a luxury item in Kuwait. It blocks solar gain before it reaches the glass, blacks out a bedroom completely, and adds a physical layer of security to ground-floor openings.

  • Foam-filled slats: heavier, quieter and better insulating, and the usual choice for bedrooms.
  • Hollow slats: lighter, suitable for stores and service openings.
  • Perforated slats: allow some air and filtered light while still blocking the view in.
  • Manual operation by strap or crank: no power required, sensible on smaller openings.
  • Tubular motor operation: effectively necessary on wide or high openings, and needs a power point and switch position agreed in advance.
  • Box position: surface-mounted above the opening, or built into the wall. The built-in option has to be decided during construction.

The steel side: structure, gates and balustrades

The second half of our aluminium, glass and steel division is metalwork. Our fabricators are part of the site team rather than an outside workshop called in to make a gate, so structural and decorative steel are detailed together with the rest of the build.

  • Structural steel: beams and columns, mezzanine frames, and roofs over spans that are awkward to bridge in concrete.
  • Steel stairs: service stairs and internal stairs with a steel stringer clad in timber or stone.
  • Gates: vehicle and pedestrian gates, sliding or swing, with automation and intercom where wanted.
  • Balustrades: wrought iron, stainless steel, or steel combined with glass, for stairs, roofs and balconies.
  • Window protection: grilles and mesh to ground-floor and courtyard openings, detailed so they still allow escape in an emergency.
  • Ancillary steel: store doors, manhole covers, condenser support frames and water tank stands.

Preparation matters more than appearance. Every fabricated item is cleaned back and primed with an anti-corrosive coat before the finish coat, because coastal humidity and airborne salt will find any steel that was painted straight over mill scale.

How we work, from survey to handover

We start with a site visit and take dimensions from the building itself rather than the drawing, and photograph existing conditions. You then receive an itemised written quotation naming the profile system, glass type and thickness class, opening arrangement, finish colour and ironmongery, so what you are approving is unambiguous.

Fabrication follows the approved sizes; installation is carried out by our own crew under the site engineer, clearing debris as we go. At handover we walk every opening: smooth operation, gasket compression, shutter alignment in its guides, and sill drainage. The work is formally handed over once any snag is put right.

Back to Aluminium, Glass & Steel Works

From Our Work

Aluminium and glass partition system for an office in Kuwait
Bronze-finish metal villa gate and fence with a geometric pattern
Structural steel welding on a Kuwait site

Frequently Asked Questions

What actually changes if I pay for thermal break profiles?

A standard profile is one continuous piece of aluminium, so outdoor heat conducts straight through to the room. A thermal break inserts an insulating strip between the outer and inner halves and interrupts that path, which reduces cooling load and stops winter condensation forming on the frame. The difference is most noticeable in rooms with large sun-facing glazing.

How much does it cost to fit new aluminium windows in a villa?

It depends on the number and size of openings, the profile system, the glass specification, the opening type, whether shutters are included, and how accessible the upper floors are. That is why we do not quote before seeing the property. We carry out a site visit, measure every opening, and issue an itemised written quotation.

Is securit glass safe in a home with children?

Toughened glass is engineered to break into small blunt granules rather than sharp shards. Where we want an extra margin, such as glass balustrades, canopies, anything overhead or at a level change, we specify laminated glass, whose layers stay bonded to the interlayer even after breakage. We select the type by position and height rather than applying one specification everywhere.

Can motorised shutters be added to existing windows?

Usually yes, using a surface-mounted box fixed above the opening outside. The part that needs planning is power to the motor and switch, which may mean a surface cable route or limited chasing. Recessed shutter boxes concealed inside the wall are normally decided during construction rather than retrofitted.

Do you handle the metalwork and the aluminium on the same project?

Yes, and that is the point of combining them. Gates, balustrades, window protection and the windows themselves are detailed by one team in a consistent design language and finish, under one contract. It removes the familiar argument between an aluminium supplier and a metal workshop about who owns the opening.

How long does fabrication and installation take?

It depends on the number of openings, the profile and glass specification and its availability, and whether the building is ready to receive the installation. After the site visit we include a staged programme in the quotation and work to it, provided the site is handed to us ready on the agreed dates.

Which finish lasts longer on aluminium in Kuwait, powder coating or anodising?

Both last well on a properly cleaned and pretreated profile. Polyester powder coating gives the widest colour range, including wood effects, and hides small marks; anodising gives a harder metallic surface in fewer tones. On seafront plots either finish needs a fresh-water rinse every few months so salt does not sit in the frame corners.

Ready to Start Your Project?

Call us, send a WhatsApp message or email us to book a site visit and a clear written quotation.

Call Now WhatsApp Quote